An Easy Instruction for Installing a Bathtub
An Easy Instruction for Installing a Bathtub
Blog Article
How do you really feel in relation to Installing A Bathtub?
Mounting a bath tub isn't specifically brain surgery, yet it does require strong plumbing, carpentry, as well as sometimes, tiling abilities. Changing an old bath tub with a brand-new one is also a moderately hard project. If the old tub is readily available, the project can move quickly; if you have to open up a wall surface to get rid of the old bathtub as well as position the brand-new bathtub, the job is a lot harder. In either case, the project is within a residence handyman's skills, although you will need an assistant to move out the old bathtub and also embeded in the new one. Make sure you have actually certified on your own for the task as well as are comfortable trying it. As opposed to hiring a professional to take control of a halfway-completed project, it is much better to consider employing one before you begin. Possibilities are you might need an expert plumber to make tube links.
This short article will certainly assist you install a new bathtub in your shower room if you have actually already acquired a brand-new bathtub and don't need to transform the plan of your previous water pipelines.
Your devices as well as product list need to consist of the following:
Removing Old Touches
If you require to replace old taps with brand-new ones as a part of your installment, after that the first thing you should do is disconnect the water. After doing so, turn on the faucets to drain pipes any type of water remaining in the system. The procedure of eliminating the existing faucets can be fairly problematic because of the restricted access that is often the situation.
Utilize a container wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipes to the faucets. Have a towel all set for the remaining water that will originate from the pipelines. Once the supply pipes have actually been removed, utilize the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the solitary taps from transforming throughout this procedure. As soon as the faucets have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any kind of old sealing compound.
Before carrying on to fit the new faucets, contrast the pipe links on the old taps to the new taps. If the old taps are longer than the new taps, after that a shank adapter is required for the new taps to fit.
Suitable New Taps
If the tails of the new taps are plastic, then you will certainly need a plastic connector to prevent damage to the string. One end of the connector fits on the plastic tail of the tap and also the various other end offers a link to the current supply pipelines.
If you require to fit a monobloc, then you will call for lowering couplers, which connects the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next off, place the faucet in the mounting hole in the bath/basin making sure that the washing machines are in location in between the tap and the sink. Secure the tap in place with the producer given backnut. As soon as the faucet is safely in place, the supply pipes can be attached to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with typical tap connectors. The former type needs to be attached to the faucet ends initially, tightening only by hand. The supply pipelines can later be connected to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Mounting the Bathtub
Using both wood boards under its feet, position the bath tub in the required placement. The wood boards are helpful in evenly spreading the weight of the bath tub over the area of the boards rather than concentrating all the weight onto 4 tiny points.
The following goal is to make certain that the tub is leveled all round. This can be attained by inspecting the level and changing the feet on the tub till the spirit level reads level.
To set up taps, fit the bottom of the furthest adaptable tap connector to the ideal supply pipeline by making a compression join; then do the exact same for the other tap.
Turn on the water as well as examine all joints as well as brand-new pipework for leaks as well as tighten them if necessary. Fill the tub as well as likewise check the overflow electrical outlet as well as the regular electrical outlet for leakages.
Finally, repair the bath paneling as described in the manufacturer's instruction manual. Tiling and also securing around the bathtub should wait up until the tub has been used a minimum of when as this will certainly resolve it right into its final placement.
Planning for the Setup
First of all, the sustaining frame provided with the bath needs to be fitted (if required) according to the maker's directions. Next, fit the faucets or mixer to the bath tub. When fitting the tap block, it is essential to make sure that if the tap includes a plastic washer, it is fitted in between the bathroom as well as the faucets. On a plastic bathroom, it is also reasonable to fit a sustaining plate under the faucets unit to avoid stress on the bath tub.
Fit the flexible faucet connectors to the bottom of both taps using 2 nuts and olives (often provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet via the hole in the bathroom. Use the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. Make certain you make use of all of the supplied washers.
Link the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bath must now be ready to be suited its last placement.
Tiling Around the Bath tub
In the area where the bathroom satisfies the ceramic tile, it is essential to seal the joins with a silicone rubber caulking. This is necessary as the fitting can move enough to fracture an inflexible seal, causing the water to permeate the wall between the bathroom and the tiling, resulting in difficulties with moisture as well as possible leakages to the ceiling listed below.
You can pick from a variety of coloured sealers to blend in your fixtures and also fittings. They are sold in tubes and cartridges, as well as are capable of sealing spaces approximately a size of 3mm (1/8 inch). If you have a bigger gap to load, you can load it with spins of drenched paper or soft rope. Keep in mind to constantly fill the tub with water prior to sealing, to permit the movement experienced when the bathtub is in usage. The sealant can break fairly early if you do not take into consideration this activity before securing.
Additionally, ceramic coving or quadrant floor tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are additionally easily available on the market. It is a good idea to fit the ceramic tiles utilizing waterproof or water resistant adhesive and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a passionate person who reads on How to Install a Bathtub, I figured sharing that information was really helpful. Sharing is caring. Helping others is fun. Thanks for your time invested reading it.
Call Us Now Report this page